PSI - Issue 53

First page Table of contents Previous page 289 Next page Last page

ScienceDirect Available online at www.sciencedirect.com ScienceDirect Structural Integrity Procedia 00 (2022) 000 – 000 Available online at www.sciencedirect.com ScienceDirect Structural Integrity Procedia 00 (2022) 000 – 000 Available online at www.sciencedirect.com

www.elsevier.com/locate/procedia www.elsevier.com/locate/procedia

Procedia Structural Integrity 53 (2024) 246–253

© 2023 The Authors. Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (https://creativecommons.org/licenses/by-nc-nd/4.0 ) Peer-review under responsibility of the scientific committee of the ESIAM23 chairpersons Abstract Additive manufacturing (AM) is a developing manufacturing method and has become an advanced one for producing unique and complex shaped parts. This method is promising for manufacturing of titanium alloys, as it allows to significantly reduce the costs of titanium parts compared to conventional manufactured methods. In this work, the effect of post heat treatment on the microstructure evolution and corrosion resistance of AM titanium alloy in a hydrochloric acid solution was studied by comparing it with a conventional manufactured one (wrought). As AM was chosen selective laser melting method which performed by 3D Metal Tech company (Ukraine). The corrosion resistance was studied by electrochemical and immersion test according to ASTM G 31-72 standard. The results obtained via corrosion tests show that the anti-corrosion properties of AM titanium alloy was worse than for the wrought one, which was explained by the presence of a non-equilibrium metastable martensitic phase and residual stresses in AM titanium alloy. Microstructural results showed that post heat treatment led to the reduction of the non-equilibrium phase martensitic α′, relief of r esidual stresses, and forma tion of the β phase, which has higher corrosion resistance. These changes lead to an improvement of the corrosion resistance of AM titanium alloy and result in the performance comparable to that of conventional wrought titanium alloy. These results indicate that the selective laser melting method of AM accompanied by the post heat treatment processes can be used to produce AM Ti6Al4V parts in comparison to wrought ones. © 2023 The Authors. Published by ELSEVIER B.V. This is an open access article under the CC BY-NC-ND license ( https://creativecommons.org/licenses/by-nc-nd/4.0 ) Peer-review under responsibility of the scientific committee of the ESIAM23 chairpersons Keywords: Ti6Al4V, additive manufacturing, heat treatment, corrosion resistance. Third European Conference on the Structural Integrity of Additively Manufactured Materials (ESIAM23) Improving corrosion resistance of additively manufactured Ti6Al4V titanium alloy by post heat treatment Serhii Lavrys*, Mariia-Olena Danyliak, Iryna Pohrelyuk, Oleh Tkachuk Karpenko Physico-Mechanical Institute of the NAS of Ukraine, 5, Naukova str., 79060, Lviv, Ukraine Abstract Additive manufacturing (AM) is a developing manufacturing method and has become an advanced one for producing unique and complex shaped parts. This method is promising for manufacturing of titanium alloys, as it allows to significantly reduce the costs of titanium parts compared to conventional manufactured methods. In this work, the effect of post heat treatment on the microstructure evolution and corrosion resistance of AM titanium alloy in a hydrochloric acid solution was studied by comparing it with a conventional manufactured one (wrought). As AM was chosen selective laser melting method which performed by 3D Metal Tech company (Ukraine). The corrosion resistance was studied by electrochemical and immersion test according to ASTM G 31-72 standard. The results obtained via corrosion tests show that the anti-corrosion properties of AM titanium alloy was worse than for the wrought one, which was explained by the presence of a non-equilibrium metastable martensitic phase and residual stresses in AM titanium alloy. Microstructural results showed that post heat treatment led to the reduction of the non-equilibrium phase martensitic α′, relief of r esidual stresses, and forma tion of the β phase, which has higher corrosion resistance. These changes lead to an improvement of the corrosion resistance of AM titanium alloy and result in the performance comparable to that of conventional wrought titanium alloy. These results indicate that the selective laser melting method of AM accompanied by the post heat treatment processes can be used to produce AM Ti6Al4V parts in comparison to wrought ones. © 2023 The Authors. Published by ELSEVIER B.V. This is an open access article under the CC BY-NC-ND license ( https://creativecommons.org/licenses/by-nc-nd/4.0 ) Peer-review under responsibility of the scientific committee of the ESIAM23 chairpersons Keywords: Ti6Al4V, additive manufacturing, heat treatment, corrosion resistance. Third European Conference on the Structural Integrity of Additively Manufactured Materials (ESIAM23) Improving corrosion resistance of additively manufactured Ti6Al4V titanium alloy by post heat treatment Serhii Lavrys*, Mariia-Olena Danyliak, Iryna Pohrelyuk, Oleh Tkachuk Karpenko Physico-Mechanical Institute of the NAS of Ukraine, 5, Naukova str., 79060, Lviv, Ukraine

* Corresponding author. Tel.: +38-093-842-1426; fax: +38-032-264-9427. E-mail address: lavrys92@gmail.com * Corresponding author. Tel.: +38-093-842-1426; fax: +38-032-264-9427. E-mail address: lavrys92@gmail.com

2452-3216 © 2023 The Authors. Published by ELSEVIER B.V. This is an open access article under the CC BY-NC-ND license ( https://creativecommons.org/licenses/by-nc-nd/4. 0 ) Peer-review under responsibility of the scientific committee of the ESIAM23 chairpersons 2452-3216 © 2023 The Authors. Published by ELSEVIER B.V. This is an open access article under the CC BY-NC-ND license ( https://creativecommons.org/licenses/by-nc-nd/4. 0 ) Peer-review under responsibility of the scientific committee of the ESIAM23 chairpersons

Made with FlippingBook Ebook Creator