PSI - Issue 64

Kevin Isaac Escobar et al. / Procedia Structural Integrity 64 (2024) 1476–1483 Kevin Isaac Escobar / Structural Integrity Procedia 00 (2019) 000 – 000

1483

8

carbon fibres coated with latex resin. To reach the maximum load a bonded length of 450 mm was shown to be sufficient. For basalt fibres, although a bonded length of 400 mm demonstrated good capacity, the maximum strength of the textile could not be obtained. - Regardless of the TRM composition, slippage between the textile and the matrix with a subsequent fibres rupture was the prevalent failure mode in the bond tests. The influence of the substrate resistance was found to be negligible. Acknowledgements The study presented in this paper was developed in the scope of research project PID2021-123701OB-C21 funded by the Spanish Ministry of Science and Innovation (MCIN/AEI/10.13039/501100011033/) and the European Regional Development Funds (ERDF) as well as research project TED2021-130272B-C21 funded by the Spanish Ministry of Science and Innovation (MCIN/AEI/10.13039/501100011033) and the European Union NextGenerationEU/ PRTR. The first author would like to acknowledge the FI SDUR scholarship program for their invaluable support. The authors would also like to acknowledge the dedicated LATEM laboratory staff of the UPC, whose expertise and assistance were important throughout the experimental campaign. Additionally, the authors would like to thank Mapei and their employees, for their courtesy supplying required materials and giving technical assistance when needed. References AC434. (2016). Acceptance criteria for masonry and concrete strengthening using fabric-reinforced cementitious matrix (FRCM) and steel reinforced grout (SRG) composite systems AC434. ICC-ES International Code Council Evaluation Service. Alexandre, V. J. F., Boshoff, W. P., & Combrinck, R. (2023). Damage evaluation and mechanisms of textile reinforced concrete during telescopic failure. Construction and Building Materials, 403. https://doi.org/10.1016/j.conbuildmat.2023.133055 Arboleda, D., Carozzi, F. G., Nanni, A., & Poggi, C. (2016). Testing Procedures for the Uniaxial Tensile Characterization of Fabric-Reinforced Cementitious Matrix Composites. Journal of Composites for Construction, 20(3). https://doi.org/10.1061/(asce)cc.1943-5614.0000626 Calabrese, A. S., D’antino, T., Colombi, P., & Poggi, C. (2022). Long-Term Behavior of PBO FRCM and Comparison with Other Inorganic-Matrix Composites. Materials, 15(9). https://doi.org/10.3390/ma15093281 D’Ambrisi, A., Feo, L., & Focacci, F. (2012). Bond -slip relations for PBO-FRCM materials externally bonded to concrete. Composites Part B: Engineering, 43(8), 2938 – 2949. https://doi.org/10.1016/j.compositesb.2012.06.002 D’Antino, Calabrese, A. S., Colombi, P., & Poggi, C. (2023). Experimental and numerical investigation on the tensile behavior of PBO FRCM composites with textile lap splice. Construction and Building Materials, 363. https://doi.org/10.1016/j.conbuildmat.2022.129437 D’Antino, & Papanicolaou, C. (2017). Mechanical characterization of textile reinforced inorganic -matrix composites. Composites Part B: Engineering, 127, 78 – 91. https://doi.org/10.1016/j.compositesb.2017.02.034 Donnini, J., & Corinaldesi, V. (2017). Mechanical characterization of different FRCM systems for structural reinforcement. Construction and Building Materials, 145, 565 – 575. https://doi.org/10.1016/j.conbuildmat.2017.04.051 EN 1015-11. (2019). Methods of test for mortar for masonry Part 11: Determination of flexural and compressive strength of hardened mortar. European Committee for Standardization (CEN). EN 12390-3. (2019). Testing hardened concrete Part 3: Compressive strength of test specimens. European Committee for Standardization (CEN). Ferrier, E., Rabinovitch, O., & Michel, L. (2016). Mechanical behavior of concrete – resin/adhesive – FRP structural assemblies under low and high temperatures. Construction and Building Materials, 127, 1017 – 1028. https://doi.org/10.1016/j.conbuildmat.2015.12.127 Koutas, L. N., Tetta, Z., Bournas, D. A., & Triantafillou, T. C. (2019). Strengthening of Concrete Structures with Textile Reinforced Mortars: State of-the-Art Review. Journal of Composites for Construction, 23(1). https://doi.org/10.1061/(asce)cc.1943-5614.0000882 Raoof, S. M., & Bournas, D. A. (2017). TRM versus FRP in flexural strengthening of RC beams: Behaviour at high temperatures. Construction and Building Materials, 154, 424 – 437. https://doi.org/10.1016/j.conbuildmat.2017.07.195 Rawat, P., Liu, S., Guo, S., Zillur Rahman, M., Yang, T., Bai, X., et al. (2022, September 12). A state-of-the-art review on mechanical performance characterization and modelling of high-performance textile reinforced concretes. Construction and Building Materials. Elsevier Ltd. https://doi.org/10.1016/j.conbuildmat.2022.128521 RILEM Technical Committee 232-TDT, Brameshuber, W., Hinzen, M., Dubey, A., Peled, A., Mobasher, B., et al. (2016). Recommendation of RILEM TC 232-TDT: test methods and design of textile reinforced concrete. Materials and Structures/Materiaux et Constructions, 49(12), 4923 – 4927. https://doi.org/10.1617/s11527-016-0839-z Signorini, C., Nobili, A., Cedillo González, E. I., & Siligardi, C. (2018). Silica coating for interphase bond enhancement of carbon and AR-glass Textile Reinforced Mortar (TRM). Composites Part B: Engineering, 141, 191 – 202. https://doi.org/10.1016/j.compositesb.2017.12.045 Sneed, L. H., D’Antino, T., Carloni, C., & Pellegrino, C. (2015). A comparison of the bond behavior of PBO -FRCM composites determined by double-lap and single-lap shear tests. Cement and Concrete Composites, 64, 37 – 48. https://doi.org/10.1016/j.cemconcomp.2015.07.007 Tetta, Z. C., & Bournas, D. A. (2016). TRM vs FRP jacketing in shear strengthening of concrete members subjected to high temperatures. Composites Part B: Engineering, 106, 190 – 205. https://doi.org/10.1016/j.compositesb.2016.09.026