PSI - Issue 14

ScienceDirect Available online at www.sciencedirect.com Av ilable o line at ww.sciencedire t.com Sci ceDirect Structural Integrity Procedia 00 (2016) 000 – 000 Procedia Structu al Integrity 14 (2019) 314–321 ScienceDirect Structural Integrity Procedia 00 (2018) 000–000 Available online at www.sciencedirect.com ScienceDirect Structural Integrity Procedia 00 (2018) 000–000

www.elsevier.com/locate/procedia

www.elsevier.com/locate/procedia

www.elsevier.com/locate/procedia 2nd International Conference on Structural Integrity and Exhibition 2018 Influence of retrogression and re-ageing heat treatment on the fatigue crack growth behavior of 7010 aluminum alloy M S Nandana a , K Udaya Bhat a, *, C M Manjunatha b a Department of Metallurgical and Materials Engineering, National Institute of Technology Karnataka, Surathkal, Mangalore 575025, India b Structural Technologies Division, CSIR-National Aerospace Laboratories, Bangalore 560017, India Aluminum alloys are widely used in aircraft structural components where light weight, high strength and good corrosion resistance are the primary requirements. These alloys are generally used in peak-aged (T6) condition in which they are susceptible for stress corrosion cracking. In the recent years, retrogression and re-ageing (RRA) treatment on aluminum alloy is carried out to enhanc heir corrosion resistance main aining the ultimate te sile strength. The aim of this work was to study the influence of RRA treatment on the fatigue crack growth rate (FCGR) behavior. The 7010 aluminum alloy was heat treated to two different conditions i.e., T6 and RRA. The microstructures of these alloys were characterized by using TEM. Standard compact tension (CT) specimens were prepared and FCGR tests were carried out by using a 100 kN servo-hydraulic test machine as per ASTM E647-15e1. The constant amplitude FCGR tests were carried out at a stress ratio, R = 0.5 using sine wave loading pattern at 10 Hz. Crack length was monitored by following compliance technique. Microstructural studies show that RRA treated alloy contain fine and densely populated precipitates in the matrix along with coarse and discontinuous precipitates in the grain boundary. The fatigue crack growth rate was observed to reduce along with an increase in the threshold stress intensity factor range (ΔK th ) for RRA treated alloy compared to the T6 alloy. The mechanisms for reduction in fatigue crack growth rate of RRA treated alloy is attributed to the microstructural modifications. The increased resistance is expected to enhance the damage tolerance capability of the alloy. © 2018 The Authors. Published by Elsevier B.V. This is an o en access rticle u d r the CC BY-NC-ND license (https://creativecommons.org/lic ns s/by-nc-nd/4.0/) Selection d peer-rev ew under responsibility of Peer-review under responsibility of the SICE 2018 organizers. 2nd International Conference on Structural Integrity and Exhibition 2018 Influence of retrogression and re-ageing heat treatment on the fatigue crack growth behavior of 7010 luminum alloy M S Nandana a , K Ud ya Bhat a, *, C M Manjunatha b a Department of Metallurgical and Materials Engineering, National Institute of Technology Karnataka, Surathkal, Mangalore 575025, India b Structural Technologies Division, CSIR-National Aerospace Laboratories, Bangalore 560017, India Abstract Aluminum alloys are widely used in aircraft structural components where light weight, high strength and good corrosion resistance are the primary requirements. These alloys are generally used in peak-aged (T6) condition in which they are susceptible for stress corrosion cracking. In the recent years, retrogression and re-ageing (RRA) treatment on aluminum alloy is carried out to enhance their corrosion resistance maintaining the ultimate tensile strength. The aim of this work was to study the influence of RRA treatment on the fatigue crack growth rate (FCGR) behavior. The 7010 aluminum alloy was heat treated to two different conditions i.e., T6 and RRA. The microstructures of these alloys were characterized by using TEM. Standard compact tension (CT) specimens were pr pared and FCGR tests were carried o t by using a 100 kN servo-hydraulic test machine as per ASTM E647-15e1. The constant amplitude FCGR tests were carried out at a stress ati , R = 0.5 using sine wave loading pattern at 10 Hz. Crack length was monitored by following compliance technique. Microstructural studies show that RRA treated alloy contain fine and densely populated precipitates in the matrix along with coarse and discontinuous precipitates in the grain boundary. The fatigue crack growth rate was observed to reduce along with an increase in the threshold stress intensity factor range (ΔK th ) for RRA treated alloy compared to the T6 alloy. The mechanisms for reduction in fatigue crack growth rate of RRA treated alloy is attributed to the microstructural modifications. The increased resistance is expected to enhance the damage tolerance capability of the alloy. © 2018 The Authors. Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (https://creativecommons.org/licenses/by-nc-nd/4.0/) Selection and peer-review under responsibility of Peer-review under responsibility of the SICE 2018 organizers. XV Portuguese Conference on Fracture, PCF 2016, 10-12 February 2016, Paço de Arcos, Portugal Thermo-mechanical modeling of a high pressure turbine blade of an airplane gas turbine engine P. Brandão a , V. Infante b , A.M. Deus c * a Department of Mechanical Engineering, Instituto Superior Técnico, Universidade de Lisboa, Av. Rovisco Pais, 1, 1049-001 Lisboa, Portugal b IDMEC, Department of Mechanical Engineering, Instituto Superior Técnico, Universidade de Lisboa, Av. Rovisco Pais, 1, 1049-001 Lisboa, Portugal c CeFEMA, Department of Mechanical Engineering, Instituto Superior Técnico, Universidade de Lisboa, Av. Rovisco Pais, 1, 1049-001 Lisboa, Portugal Abstract During their operation, modern aircraft engine components are subjected to increasingly demanding operating conditions, especially the high pressure turbine (HPT) blades. Such conditions cause these parts to undergo different types of time-dependent degradation, one of which is creep. A model using the finite element method (FEM) was developed, in order to be able to predict the creep behaviour of HPT blades. Flight data records (FDR) for a specific aircraft, provided by a commercial aviation company, were used to obtain thermal and mechanical data for three different flight cycles. In order to create the 3D model needed for the FEM analysis, a HPT blade scrap was scanned, and its chemical composition and material properties were obtained. The data that was gathered was fed into the FEM model and different simulations were run, first with a simplified 3D rectangular block shape, in order to better establish the model, and then with the real 3D mesh obtained from the blade scrap. The overall expected behaviour in terms of displacement was observed, in particular at the trailing edge of the blade. Therefore such a model can be useful in the goal of predicting turbine blade life, given a set of FDR data. © 2019 The Author . Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (https://creativecommons.org/licenses/by-nc-nd/4.0/) Selection and peer-review under responsibility of Peer-review under responsibility of the SICE 2018 organizers. Abstract © 2016 The Authors. Published by Elsevier B.V. Peer-review under responsibility of the Scientific Committee of PCF 2016. 2452-3216 © 2016 The Authors. Published by Elsevier B.V. Peer-review under responsibility of the Scientific Committee of PCF 2016. 2452-3216  2019 The Authors. Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (https://creativecommons.org/licenses/by-nc-nd/4.0/) Selection and peer-review under responsibility of Peer-review under responsibility of the SICE 2018 organizers. 10.1016/j.prostr.2019.05.039 2452-3216 © 2018 The Authors. Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (https://creativecommons.org/licenses/by-nc-nd/4.0/) Selection and peer-review under responsibility of Peer-review under responsibility of the SICE 2018 organizers. 2452-3216 © 2018 The Authors. Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (https://creativecommons.org/licenses/by-nc-nd/4.0/) Selection and peer-review under responsibility of Peer-review under responsibility of the SICE 2018 organizers. * Corresponding author. Tel.: +91-9480055475 E-mail address: udayabhatk@gmail.com Keywords: High Pressure Turbine Blade; Creep; Finite Element Method; 3D Model; Simulation. * Corresponding author. Tel.: +351 218419991. E-mail address: amd@tecnico.ulisboa.pt * Corresponding author. Tel.: +91-9480055475 E-mail address: udayabhatk@gmail.com